Difference between revisions of "Calico LC3"

From IPRE Wiki
Jump to: navigation, search
(Examples)
Line 86: Line 86:
 
You may select these two modes by issue one of the following inside your assembly program:
 
You may select these two modes by issue one of the following inside your assembly program:
  
* .SET MODE GRAPHICAL
+
* .SET MODE GRAPHICS
 
* .SET MODE SHIFT
 
* .SET MODE SHIFT
  

Revision as of 02:22, 13 December 2013

Calico LC3 is an assembly language based on the Little Computer by Patt and Patel. Calico LC3 is a language in the Calico Project.

Overview

Calico LC3 is an implementation of Patt and Patel's LC3 assembly language. The language is written in Calico Python, but appears as a full language in Calico.

In Calico, you need to first enable the LC3 language before using it:

  1. start Calico
  2. under menu -> Calico -> Languages
  3. make sure that "LC3" is checked
  4. Create a new LC3 script, or examine one of the Examples
  5. (Enable "Spreadsheet", too if you want to use it to display memory)

Special features:

  • Tracing, breakpoints, integrated IDE
  • syntax color highlighting
  • Right-click on errors takes you to line of code
  • Assembler and interpreter
  • Counts instructions executed
  • Counts machine cycles executed, estimates milliseconds to run
  • Error checking and useful error messages
  • menu -> View -> Tabs -> Locals - shows registers
  1. Shows memory as Calico Spreadsheet

Source Materials:

Special Interactive Directives

Enter these commands in the Calico Shell entry area:

Interactive Directives: 
 .help                           - shows this info
 .show memory                    - display memory as a Spreadsheet
 .assemble                       - assemble the first .asm file in Calico
 .step                           - execute the next instruction, increment PC
 .reset                          - reset LC3 to start state") 
 .raw [start [stop]]             - list meory in hex
 .list                           - list program from memory
 .dump [start [stop]]            - dump memory as program
 .regs                           - show registers
 .set pc HEXVALUE                - set PC
 .set memory HEXLOCATION HEXVALUE- set memory
 .set reg VALUE HEXVALUE         - set register
 .get pc                         - get PC
 .get memory HEXLOCATION         - get memory
 .get reg VALUE                  - get register

Instructions

ADD DR, SR1, SR2       ; Addition
ADD DR, SR1, imm5      ; Addition with Immediate
AND DR, SR1, SR2       ; Bit-wise AND
AND DR, SR1, imm5      ; Bit-wise AND with Immediate
BRx, label (where x = {n,z,p,zp,np,nz,nzp}) ; Branch
JMP BaseR              ; Jump
JSR label              ; Jump to Subroutine
JSRR BaseR             ; Jump to Subroutine in Register
LD DR, label           ; Load PC-Relative
LDI DR, label          ; Load Indirect
LDR DR, BaseR, offset6 ; Load Base+Offset
LEA, DR, label         ; Load Effective Address
NOT DR, SR             ; Bit-wise Complement
RET                    ; Return from Subroutine
RTI                    ; Return from Interrupt
ST SR, label           ; Store PC-Relative
STI, SR, label         ; Store Indirect
STR SR, BaseR, offset6 ; Store Base+Offset
TRAP immediate-vector  ; System Call

Extensions

There is an unused instruction in the original LC3 instruction set. You can use add one of two possible extensions:

  • A set of graphical instructions for drawing simple pictures
  • A shift instruction

You may select these two modes by issue one of the following inside your assembly program:

  • .SET MODE GRAPHICS
  • .SET MODE SHIFT

The SHIFT instruction takes this form:

SHIFT DestR, SR, immed6 ; shift source register (SR) by immed6 
                        ; (positive, left; negative right) and 
                        ; store in destination register (DestR)

Example:

.SET MODE SHIFT         ; This is the default mode
SHIFT R0, R1, #1        ; shift the contents of R1 to the left by one bit
                        ; and store the result in R0

The GRAPHICS instructions take these forms:

.SET MODE GRAPHICS
CLEAR                   ; Clears the Calico Screen
POKE   Rx, Ry, RSRC     ; Put the ASCII value from RSRC register to location x (Rx), y (Ry)
PEEK   Rx, Ry, RDST     ; Get the ASCII value from location x (Rx), y (Ry) and put into the RDST register 
GETCUR Rx, Ry           ; Get the cursor, storing x into Rx, and y into Ry
SETCUR Rx, Ry           ; Set the cursor, getting x from Rx, and y from Ry

The cursor will be more useful when there is a print to graphics instruction.

The Calico Screen is 32 x 64 locations in video memory.

These are the 256 values you can POKE into each video memory location:

Error creating thumbnail: Unable to save thumbnail to destination

Examples

Here is a basic Hello World assembly program.

;; helloworld.asm
.ORIG x3000
    LEA R0, HELLO
    PUTS
    HALT
HELLO .STRINGZ "Hello, World!\n"
.END

Here is a simple program to display the graphical characters. They are based on the original TRS-80 characters.

.SET MODE GRAPHICS
.ORIG x3000
        CLEAR
        AND R0,R0,#0 ;; x
        AND R1,R1,#0 ;; y
        AND R3,R3,#0 ;; char to poke
        LD R4,ROWS
        LD R6,COLS
LOOP:   POKE R0,R1,R3
        ADD R3,R3,#1
        ADD R0,R0,#1
        ADD R5,R0,R4
        BRz NEXT
        BR LOOP
        HALT
NEXT    AND R0,R0,#0
        ADD R1,R1,#1
        ADD R5,R1,R6
        BRz DONE
        BR LOOP
DONE    HALT
ROWS .FILL #-64
COLS .FILL #-4
.END

There are more examples in menu -> File -> Examples -> LC3.

Future Possibilities

  1. integrate with other languages
  2. create real code that could be executed on computer (maybe .NET/Mono VM code?)
  3. load/run binary-text files and obj files
  4. show dissassembled code